Maintenance & Care Information
Euro-Wall Systems
Product Care Instructions
Below you will find instructions on how to maintain and care for your specific door system. Following the Euro-Wall maintenance instructions and maintenance schedule will ensure the longevity of your door system's appearance and operation functionality. For questions about our maintenance policy / instructions please contact us anytime.
All Systems Maintenance & Care
Panel Protective Film
Remove all protective film from panels, frames and any other metal extrusion within 30 days of job delivery. Failure to do so could cause finish damage voiding the product warranty.
Frequency
Regular maintenance is required for all hardware, even stainless steel, to keep manufacturer’s warranty in place. Failure to provide proof of maintenance will void any warranty.
Carry out maintenance procedures with the following minimum recommendations:
- General environments - every 3 months
- Marine, industrial environments, within 5 miles of a body of water and / or a pool area - every month.
Sliding Door Systems
Maintenance & Care
Handles and Hardware
Wipe down the visible surfaces with warm soapy water on a soft cloth and then rinse off by wiping with a clean damp cloth. Spray a thin film of light machine oil or one of the corrosion preventative sprays such as CRC Marine 66®, Innox® or CorrisionX®. Be careful to avoid overspray and be sure to wipe down any overspray that does occur.
Water Management
If your sill track comes with a Euro-Wall water management configuration, ensure that all drainage points are free and clear of debris.
Sill Track and Wheels
Wipe all contaminant clear from sill track surfaces with a damp cloth and mild detergent, dry with clean soft cloth. Using a spray machine oil or one of the corrosion preventative sprays (such as, CRC Marine 66®, Innox® or CorrosionX®) spray underneath the panels and into the wheel assembly. Operate the door across the sill track to ensure the track receives lubrication / anti corrosion spray from the wheels. Repeat as necessary until the wheels and the track is properly covered. Wipe down any overspray.
Pivot Door Systems
Maintenance & Care
Hinges
Wipe down the visible surfaces with warm soapy water on a soft cloth and then rinse off by wiping with a clean damp cloth.
Locks and Hardware
Wipe down the visible surfaces with warm soapy water on a soft cloth and then rinse off by wiping with a clean damp cloth. Spray a thin film of light machine oil or one of the corrosion preventative sprays such as CRC Marine 66®, Innox® or CorrisionX®. Be careful to avoid getting these compounds on wood or fiberglass or jambs as they may cause staining. Be sure to wipe down any overspray.
Track and Bearings
Apply white petroleum jelly (Vaseline) or equivalent, to inner lip of each side of head track with a clean cloth. Distribute lubricant evenly along track. Ensure wheels and bearings receive sufficient lubricant. Wipe all contaminant from track surfaces with damp cloth and mild detergent, clean surfaces with clean soft cloth. Apply thin film for systems installed in severe environments by wiping surfaces of track with anti-corrosive substance, such as, CRC Marine 66®, Innox® or CorrosionX®.
Hangers, Pivots and Brackets
Before applying anti-corrosive substance, wipe exposed surfaces with clean soft cloth soaked in warm soapy water; then rinse, clean and dry. Spray thin film to hangers, pivots and brackets with anti-corrosive substance, such as, CRC Marine 66®, Innox® or CorrosionX®.
Folding Door Systems
Maintenance & Care
Hinges
Wipe down the visible surfaces with warm soapy water on a soft cloth and then rinse off by wiping with a clean damp cloth.
Locks and Hardware
Wipe down the visible surfaces with warm soapy water on a soft cloth and then rinse off by wiping with a clean damp cloth. Spray a thin film of light machine oil or one of the corrosion preventative sprays such as CRC Marine 66®, Innox® or CorrisionX®. Be careful to avoid getting these compounds on wood or fiberglass or jambs as they may cause staining. Be sure to wipe down any overspray.
Track and Bearings
Apply white petroleum jelly (Vaseline) or equivalent, to inner lip of each side of head track with a clean cloth. Distribute lubricant evenly along track. Ensure wheels and bearings receive sufficient lubricant. Wipe all contaminant from track surfaces with damp cloth and mild detergent, clean surfaces with clean soft cloth. Apply thin film for systems installed in severe environments by wiping surfaces of track with anti-corrosive substance, such as, CRC Marine 66®, Innox® or CorrosionX®.
Hangers, Pivots and Brackets
Before applying anti-corrosive substance, wipe exposed surfaces with clean soft cloth soaked in warm soapy water; then rinse, clean and dry. Spray thin film to hangers, pivots and brackets with anti-corrosive substance, such as, CRC Marine 66®, Innox® or CorrosionX®.
Euro-Wall 10 Year Warranty 
Euro-Wall warrants the products to be free from manufacturing defects for a period of 10 years from the date of purchase. To view our full warranty click here.